HARDCORE TOYOTA ROCK CRAWLING ARMOR
Shop by Model
Internal Roll Cages
About 4x I
0 item(s) / Total: $0
> Swing Out Tire Carrier Kit
2005 to 2018 Tacoma Tire Carrier Kit with spare tire, NATO Jerry Can Mount, and HiLift Mounts
Swing Out Tire Carrier Kit
Tire Carrier Options
Add HiLift Jack Mount [+$35.00]
Add Fold Down Cook Tray [+$148.00]
Add RotoPax Mount Bracket for up to 2 x 3 gallon packs [+$60.00]
Add Single Jerry Can Mount [+$160.00]
Add Double Jerry Can Mount [+$260.00]
License plate mount and lights [+$25.00]
Tire Mounting Plate
Toyota 4wd - 6 on 5.5" circle
Universal - see sizes below [+$6.00]
Add to Cart
Add to Wish List
4x Innovations has developed a new Swing Out Tire Carrier system that solves many problems seen on other types of carriers.
Industry's strongest hinge pivot mounted in double shear with high grade 5/16 steel support bracket
Supported by tapered roller bearings used on 1000 pound trailer axles
Massive 3/4 inch grade 8 pivot bolt
Stainless steel inner bearing sleeve to prevent corrosion
Spring loaded pin locks the hinge pivot open at 90 and 115 degrees
Spring pin rides on stainless steel skid pad, no scratches in the paint or corrosion
High strength latch uses 1" solid steel round bar catch pin and high grade steel components
Vibration proof design encloses around over 3/4 of latch pin
Spring pin locks latch closed and open
Nylon washer in latch components for wear resistance
UHMW skid pad for smooth, wear resistant closure
Tire mounts with factory Toyota size lug nuts, 6 x 5.5 bolt pattern.
Built standard to hold up to 36" tire with 6 7/16" inches from WMS to sidewall surface of tire
Custom tire mounting configurations available upon request
Optional mount for 1 or 2 x 5 gallon NATO Spec Jerry Cans or Scepter Fuel or Water carriers. Please comment in the order comments on the check out page which closure arms you'd like. (cans not included)
Optional RotoPax Mounting location for up to 2 x 3 gallon packs, RotoPax Mount (example Rotopax #DLX Pack Mount) is not included.
Optional 31" x 16" fold down camp cook table made from mild steel, which does require painting.
Optional mount for carrying a Hi Lift Jack on the tire carrier.
Optional license plate mount with license plate lights.
Ships bare steel, ready to paint with the coating and color of your choice.
For more information about tire carrier options visit this listing
Tire Carrier install guide is available here
The universal tire mounting plate has the following lug mounting patterns:
5 x 4.5" uses 3 studs
5 x 5" uses 3 studs
5 x 5.5" uses 3 studs
6 x 6" uses 3 studs
8 x 6.5" uses 4 studs
8 x 170mm uses 4 studs
*This listing is for a tire carrier kit that is the tire carrier fully assembled and welded except the latch end plate. When ordering this kit you will need to cut the main tube to length, weld the latch end plate to the end of the carrier, as well as provide sufficient mounting points for the hinge and latch catch stud. If you order this product listing with a rear bumper, your tire carrier will NOT be assembled onto the bumper. You must order the tire carrier as a part of your bumper options on the bumper product page for the tire carrier to be fully assembled and aligned onto your bumper.
96-02 4 Runner Rear Plate Bumper
2005 - 2015 Tacoma Rear High Clearance Wraparound Bumper
2005-2015 Tacoma Bolt On Rear Bumper with Dual Swing Tire Carrier
2005-2015 Tacoma Bolt On Rear Bumper with Tire Carrier
2005 - 2015 Tacoma Rear High Clearance Wraparound Bumper with Tire Carrier
1995-2004 Tacoma Rear Plate Bumper with Tire Carrier
Browse Similar Items